基于STC89C52RC單片機制作的頻率及占空比均可調程序

ID:280979 · 發表于 2019-11-5 22:37

注意  單片機必須是52rc不能用60s2

*/

#include"main.h"
#include"peizhi.h"
#include"smg.h"
#include"eeprom.h"
sfr WDT_CONTR=0XE1;
unsigned char HighRH = 0;  //高電平重載值的高字節
unsigned char HighRL = 0;  //高電平重載值的低字節
unsigned char LowRH  = 0;  //低電平重載值的高字節
unsigned char LowRL  = 0;  //低電平重載值的低字節
/***********************按鍵定義**********************************/
bit d1 = 1;
bit d2 = 1;
bit d3 = 1;

uint8 ci;
uint8 ca = 0;
uint8 ca1 = 0;
uint16 cb = 0;

void key();                //按鍵函數聲明
void ConfigPWM(unsigned int fr, unsigned char dc);  //頻率和占空比調節函數

void main()
{
bit q1 = 1;
bit q2 = 1;
bit q3 = 1;
ca = EEPROMReadByte(0);
cb = EEPROMReadByte(1)*255+EEPROMReadByte(2);

EA = 1;    //開總中斷
peizhit1(1);  //配置T0定時2ms

while(1)
{
   ConfigPWM(cb, ca); //頻率100Hz，占空比10%

   if(d1 != q1)
   {
      q1 = d1;
if(d1 == 0)
{

ca1++;
if(ca1 >= 2)
{
      ca1 = 0;
}

}
   }

   if(ca1 == 1)
   {
   if(d2 != q2)
   {
      q2 = d2;
if(d2 == 0)
{

ca++;
EEPROMSectorErase(0);
EEPROMWriteByte(0,ca);
EEPROMWriteByte(2,cb);
EEPROMWriteByte(1,cb>>8);
if(ca >= 99)
{
ca = 99;

}

}
   }

   if(d3 != q3)
   {
      q3 = d3;
if(d3 == 0)
{
if(ca>0)
{
ca--;
EEPROMSectorErase(0);
      EEPROMWriteByte(0,ca);
EEPROMWriteByte(2,cb);
EEPROMWriteByte(1,cb>>8);
   }
}
   }
   }

if(ca1 == 0)
{
   if(d2 == 0)
   {

   cb++;
   EEPROMSectorErase(0);
   EEPROMWriteByte(0,ca);
   EEPROMWriteByte(2,cb);
   EEPROMWriteByte(1,cb>>8);
   if(cb >= 200)
{
cb = 200;

}

   }

   if(d3 == 0)
   {

if(cb>0)
{
cb--;
EEPROMSectorErase(0);
EEPROMWriteByte(0,ca);
         EEPROMWriteByte(2,cb);
EEPROMWriteByte(1,cb>>8);
   }
   }

   }
xianshi1(cb);
xianshi2(ca);

}
}

void key()
{
static uint8 saomiaozhi[] = {1,1,1,1};
saomiaozhi[0] = (saomiaozhi[0]<<1) | in1;
saomiaozhi[1] = (saomiaozhi[1]<<1) | in2;
saomiaozhi[2] = (saomiaozhi[2]<<1) | in3;

if(saomiaozhi[0] == 0x00)
{
d1 = 0;
}
if(saomiaozhi[0] == 0xff)
{
d1 = 1;
}
if(saomiaozhi[1] == 0x00)
{
d2 = 0;
}
if(saomiaozhi[1] == 0xff)
{
d2 = 1;
}
if(saomiaozhi[2] == 0x00)
{
d3 = 0;
}
if(saomiaozhi[2] == 0xff)
{
d3 = 1;
}

}

/* 配置并啟動PWM，fr-頻率，dc-占空比 */
void ConfigPWM(unsigned int fr, unsigned char dc)
{
unsigned int  high, low;
unsigned long tmp;

tmp  = (11059200/12) / fr;  //計算一個周期所需的計數值
high = (tmp*dc) / 100;    //計算高電平所需的計數值
low  = tmp - high;       //計算低電平所需的計數值
high = 65536 - high + 12; //計算高電平的重載值并補償中斷延時
low  = 65536 - low  + 12; //計算低電平的重載值并補償中斷延時
HighRH = (unsigned char)(high>>8); //高電平重載值拆分為高低字節
HighRL = (unsigned char)high;
LowRH  = (unsigned char)(low>>8);  //低電平重載值拆分為高低字節
LowRL  = (unsigned char)low;
TMOD &= 0xF0; //清零T0的控制位
TMOD |= 0x01; //配置T0為模式1
TH0 = HighRH; //加載T0重載值
TL0 = HighRL;
ET0 = 1;       //使能T0中斷
TR0 = 1;       //啟動T0
PWMOUT = 1;    //輸出高電平
}

/* T0中斷服務函數，產生PWM輸出 */
void InterruptTimer0() interrupt 1
{
if (PWMOUT == 1)  //當前輸出為高電平時，裝載低電平值并輸出低電平
{
      TH0 = LowRH;
      TL0 = LowRL;
      PWMOUT = 0;
}
else             //當前輸出為低電平時，裝載高電平值并輸出高電平
{
      TH0 = HighRH;
      TL0 = HighRL;
      PWMOUT = 1;
}
}

/* T0中斷服務函數，完成數碼管、按鍵掃描與秒表計數 */
void t1() interrupt 3
{

TH1 = T1RH;  //重新加載重載值
TL1 = T1RL;
ci++;
ssmg();    //數碼管掃描


if(ci>=2)
{
ci = 0;
key();
}
}