日韩精品一区国产偷窥在线,日本熟妇中文字幕三级久久,男男纯肉被CAO哭高H腿交动漫

#include <reg51.h>
#include <intrins.h>
sbit SDA=P3^6; // 此引腳須上拉 4.7K 電阻至 VCC
sbit SCL=P3^7; // 此引腳須上拉 4.7K 電阻至 VCC
sbit beep=P1^5;
unsigned int range=0;
//unsigned int range1=0;
//unsigned int range2=0;
//unsigned int range3=0;
//unsigned int min=0;
void delay50us_chengxv(void) //誤差 0us
{
unsigned char a,b;
for(b=9;b>0;b--)
for(a=1;a>0;a--);
}
void delay500ms(void) //誤差 0us
{
unsigned char a,b,c;
for(c=205;c>0;c--)
for(b=116;b>0;b--)
for(a=9;a>0;a--);
}
void delay300ms(void) //誤差 0us
{
unsigned char a,b,c;
for(c=5;c>0;c--)
for(b=212;b>0;b--)
for(a=140;a>0;a--);
}
void beepcv()
{
unsigned int a;
if(range<=1500&&range>=0)
{
if(range<=1500&&range>=900)
{
for(a=600;a>0;a--)
{
beep=1;
delay1(10);
beep=0;
delay1(10);
delay1(175);
}
}
else if(range>=300&&range<900)
{
for(a=600;a>0;a--)
{
beep=1;
delay1(10);
beep=0;
delay1(10);
delay1(100);
}
}
else if(range>=0&&range<300)
{
for(a=600;a>0;a--)
{
beep=1;
delay1(10);
beep=0;
delay1(10);
delay1(50);
}
}
}
}
void delay(void) //short delay 使用速度較快的單片機時，I2C 通訊可能不正常，在此函數中多加 4～8 個_nop_();即可
{
_nop_(); _nop_(); _nop_(); _nop_();
_nop_(); _nop_(); _nop_(); _nop_();
_nop_(); _nop_(); _nop_(); _nop_();
_nop_(); _nop_(); _nop_(); _nop_();
}
void start(void) //I2C start
{
SDA = 1;
delay();
SCL = 1;
delay();
SDA = 0;
delay();
}
void stop(void) //I2C stop
{
SDA = 0;
delay();
SCL = 1;
delay();
SDA = 1;
delay();
}
void ack(void) //ack
{
unsigned char i;
SCL = 1;
delay();
while(SDA == 1 && i < 200)
{
i++;
}
SCL = 0;
delay();
}
void no_ack() //not ack
{
SDA = 1;
delay();
SCL = 1;
delay();
SCL = 0;
delay();
}
void i2c_write_byte(unsigned char dat) //write a byte
{
unsigned char i;
SCL = 0;
for(i = 0; i < 8; i++)
{
if(dat & 0x80)
{
SDA = 1;
}
else
{
SDA = 0;
}
dat = dat << 1;
delay();
SCL = 1;
delay();
SCL = 0;
delay();
}
SDA = 1;
delay();
}
unsigned char i2c_read_byte(void) //read a byte
{
unsigned char i,dat;
SCL = 0;
delay();
SDA = 1;
delay();
for(i = 0; i < 8; i++)
{
SCL = 1;
delay();
dat = dat << 1;
if(SDA == 1)
{
dat++;
}
SCL = 0;
delay();
}
return dat;
}
void init_i2c(void) //i2c init
{
SDA = 1;
SCL = 1;
}
void write_byte(unsigned char address,unsigned char reg,unsigned char command) //address+register+command
{
init_i2c();
start();
i2c_write_byte(address);
ack();
i2c_write_byte(reg);
ack();
i2c_write_byte(command);
ack();
stop();
}
unsigned char read_byte(unsigned char address,unsigned char reg) //address(with bit 0 set) + register
{
unsigned char dat;
init_i2c();
start();
i2c_write_byte(address);
ack();
i2c_write_byte(reg);
ack();
start();
i2c_write_byte(address+1);
ack();
delay();delay();delay();delay();delay(); //此處延時對于 STC89C 系列單片機，可以刪除，如果對于快速單
//片機，需要加至少 50us 的延時，才可以可靠讀到數據
dat = i2c_read_byte();
no_ack();
stop();
return dat;
}
void delayms(unsigned int ms) //delay ms
{
unsigned char i;
unsigned int j;
for(i=0;i<110;i++)
for(j=0;j<ms;j++);
}
/*void change_i2c_address(unsigned char addr_old, unsigned char addr_new)
// addr_old is the address now, addr_new will be the new address
{ //that you want change to
delayms(2000); // Protect the eeprom ,you can delete this sentence
write_byte(addr_old,2,0x9a);
delayms(1);
write_byte(addr_old,2,0x92);
delayms(1);
write_byte(addr_old,2,0x9e);
delayms(1);
write_byte(addr_old,2, addr_new);
delayms(500); //Protect the eeprom, you can delete this sentence
}
void config_0x71_0x7d(unsigned char addr_old, unsigned char flag)
//flag will be 0x71,0x72,0x73,0x74,0x7a,0x7b,0x7c,0x7d
{ //that you want change to
delayms(2000); // Protect the eeprom ,you can delete this sentence
write_byte(addr_old,2,0x9c);
delayms(1);
write_byte(addr_old,2,0x95);
delayms(1);
write_byte(addr_old,2,0x98);
delayms(1);
write_byte(addr_old,2, flag);
delayms(500); //Protect the eeprom, you can delete this sentence
}*/
unsigned int detect(unsigned char address,unsigned char command) //0xe8(address) + 0x30(command)
{
unsigned int distance,count;
write_byte(address,2,command); //use command "0x30" to detect the distance
delayms(1); //安全延時,如果顯示不清晰可以將延時調大一些
//delayms(80); //如果是探測溫度此處延時需根據表 1 所列時間相應延長
count=800;
while(--count || !SCL) //等待探測結束，count 值調小將減小探測等待時間
{
; // 空語句
// DigDisplay(range); //顯示語句，可根據需要保留或刪除
}
// while(!SCL)display(range); //you can delete "display(range)"
//通過查詢 SCL 線來智能識別探測是否結束，使用本語句可刪除上條語句(count=800;while…)以節省探測時間
distance=read_byte(address,2);
distance <<= 8;
distance += read_byte(address,3);
return distance; //return 16 bit distance in millimeter
}
void main(void)
{
//change_i2c_address(0xe8,0xfe); //change default address 0xe8 to 0xfe
while(1)
{
range = detect(0xe8,0x30);
//0xe8 is the address; 0x30 is the command.you just need the only one sentence to get the range.
beepcv();
}
}

復制代碼

亚洲春色中文字幕久久久-三上亚,一吻二脱三床四吻胸,国产真实伦对白视频全集,在线毛片观看,精品成品入口黄网,国产毛aⅴ片久久久,亚洲AV色香蕉一区二区三区老师,萧皇后A级艳片,色情日本视频更新,99久久亚洲精品日本无码