亚洲春色中文字幕久久久-三上亚,啪啪啪网站,国产午夜伦鲁鲁,四虎影视在线永久免费观看,中国精品视频一区二区 ,半夜妺妺叫我吃她胸,亚洲无线看天堂av,人妻互换免费中文字幕,被群CAO的合不拢腿H的皇后,护士的下面又湿又紧10P

標題: 51單片機匯編語言八路搶答器數組越界問題 [打印本頁]

作者: 青銅左腳 時間: 2026-7-7 22:01
標題: 51單片機匯編語言八路搶答器數組越界問題
目的：使用51單片機P0口驅動共陽數碼管實現8路搶答器，上電默認顯示0，然后1-8按鍵被按下就顯示該數值，且后續任何按鍵按下無效，按復位鍵從來。問題：代碼1剛上電，數碼管無任何顯示！！！；1-8按鍵功能正常。
問題分析：通過KEIL調試發現初始化A=00，1：LOOP行完后A是0XC0，P0是0XC0（顯示數字0）；2：第一輪結束然后跳轉到LOOP執行完后A變成0X00(TABLE【192的偏移地址是多少？越界了所以是0X00】)，P0又變?yōu)?0（顯示數字0.），然后程序不斷循環1、2
解決方案：讓循環發生在P0賦值0之后、或者每次循環都重新賦值P0為0，代碼B就是讓循環發生在P0賦值之后，這樣P0端口在沒有按鍵按下的時間都是固定值（循環前被賦值MOV P0,A）
代碼A：
KEY2 BIT P2.1
KEY3 BIT P2.2
KEY4 BIT P2.3

KEY5 BIT P2.4
KEY6 BIT P2.5
KEY7 BIT P2.6
KEY8 BIT P2.7

ORG 00H
MAIN:
   MOV A,#00
   MOV DPTR,#TABLE
LOOP:
      MOVC A,@A+DPTR
   MOV P0,A

KEYA:JB KEY1,KEYB
      MOV A,#1
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYB:JB KEY2,KEYC
      MOV A,#2
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYC:JB KEY3,KEYD
   MOV A,#3
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYD:JB KEY4,KEYE
   MOV A,#4
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYE:JB KEY5,KEYF
   MOV A,#5
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYF:JB KEY6,KEYG
      MOV A,#6
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYG:JB KEY7,KEYH
      MOV A,#7
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYH:JB KEY8,LOOP
      MOV A,#8
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $


TABLE:DB 0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8
   DB 0x80,0x90,0x88,0x83,0xC6,0xa1,0x86,0x8e
      END
/***********************/
代碼B：
KEY2 BIT P2.1
KEY3 BIT P2.2
KEY4 BIT P2.3

KEY5 BIT P2.4
KEY6 BIT P2.5
KEY7 BIT P2.6
KEY8 BIT P2.7

ORG 00H
MAIN:
   MOV A,#00
   MOV DPTR,#TABLE
LOOP:
      MOVC A,@A+DPTR
   MOV P0,A

KEYA:JB KEY1,KEYB
      MOV A,#1
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYB:JB KEY2,KEYC
      MOV A,#2
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYC:JB KEY3,KEYD
   MOV A,#3
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYD:JB KEY4,KEYE
   MOV A,#4
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYE:JB KEY5,KEYF
   MOV A,#5
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYF:JB KEY6,KEYG
      MOV A,#6
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYG:JB KEY7,KEYH
      MOV A,#7
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

KEYH:JB KEY8,KEYA
      MOV A,#8
      MOVC A,@A+DPTR
   MOV P0,A
      JMP $

TABLE:DB 0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8
   DB 0x80,0x90,0x88,0x83,0xC6,0xa1,0x86,0x8e
      END

作者: 188610329 時間: 2026-7-8 22:37
匯編的目的，就是程序簡單化，沒必要，把簡單的應用，搞到復雜化吧？

你的按鍵都在 P2, 數碼管在 P0, 這么寫不是更簡單？

Start:
MOV P0,#0C0H
MOV DPTR,#TABLE
CLR A
MOV R2,A
Check_key:
CPL A
XOR A,P2
JZ Check_key
Key_Analysis:
RRC A
INC R2
JNC Key_Analysis
Key_Disp:
MOV A,R2
MOVC A,@A+DPTR
MOV P0,A
SJMP $

TABLE:DB 0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8
DB 0x80,0x90,0x88,0x83,0xC6,0xa1,0x86,0x8e
END

歡迎光臨 (http://www.denmoz.com/bbs/)