精品伊人久久久大香线蕉软件,日本在线视频一区二区,继室肉欲H-继室肉欲H

/*---------------------------------------------------------------------*/
/* --- STC MCU Limited ------------------------------------------------*/
/* --- STC 1T Series MCU Demo Programme -------------------------------*/
/* 如果要在程序中使用此代碼,請在程序中注明使用了STC的資料及程序 */
/*---------------------------------------------------------------------*/
/************* 功能說明 **************
使用Timer0模擬6通道PWM驅動程序。
輸出為 P3.0 ~ P3.5, 對應 PWM0 ~ PWM5.
定時器中斷頻率一般不要超過100KHZ, 留足夠的時間給別的程序運行.
本例子使用11.0592MHZ時鐘, 25K的中斷頻率, 250級PWM, 周期為10ms.
中斷里處理的時間不超過6us, 占CPU時間大約為15%.
******************************************/
//芯片是STC15F101W的
#include <reg52.h>
#define MAIN_Fosc 11059200UL //定義主時鐘
#define Timer0_Rate 25000 //中斷頻率
typedef unsigned char u8;
typedef unsigned int u16;
typedef unsigned long u32;
sfr AUXR = 0x8E;
sfr P3M1 = 0xB1; //PxM1.n,PxM0.n =00--->Standard, 01--->push-pull
sfr P3M0 = 0xB2; // =10--->pure input, 11--->open drain
#define Timer0_Reload (65536UL -(MAIN_Fosc / Timer0_Rate)) //Timer 0 重裝值
//************** PWM8 變量和常量以及IO口定義 ***************
//******************** 8通道8 bit 軟PWM ********************
#define PWM_DUTY_MAX 250 // 0~255 PWM周期, 最大255
#define PWM_ON 1 // 定義占空比的電平, 1 或 0
#define PWM_OFF (!PWM_ON)
#define PWM_ALL_ON (0xff * PWM_ON)
u8 bdata PWM_temp1; //影射一個RAM，可位尋址，輸出時同步刷新
sbit P_PWM0 = PWM_temp1^0; // 定義影射RAM每位對應的IO
sbit P_PWM1 = PWM_temp1^1;
sbit P_PWM2 = PWM_temp1^2;
sbit P_PWM3 = PWM_temp1^3;
sbit P_PWM4 = PWM_temp1^4;
sbit P_PWM5 = PWM_temp1^5;
u8 pwm_duty; //周期計數值
u8 pwm[6]; //pwm0~pwm5 為0至5路PWM的寬度值
bit B_1ms;
u8 cnt_1ms;
u8 cnt_20ms;
/**********************************************/
void main(void)
{
u8 i;
P3M0 = 0x00;
P3M1 = 0x00;
AUXR |= (1<<7); // Timer0 set as 1T mode
TMOD &= ~(1<<2); // Timer0 set as Timer
TMOD &= ~0x03; // Timer0 set as 16 bits Auto Reload
TH0 = Timer0_Reload / 256; //Timer0 Load
TL0 = Timer0_Reload % 256;
ET0 = 1; //Timer0 Interrupt Enable
PT0 = 1; //高優先級
TR0 = 1; //Timer0 Run
EA = 1; //打開總中斷
cnt_1ms = Timer0_Rate / 1000; //1ms計數
cnt_20ms = 20;
for(i=0; i<6; i++) pwm[i] = i * 5 + 5; //給PWM一個初值
while(1)
{
if(B_1ms) //1ms到
{
B_1ms = 0;
if(--cnt_20ms == 0) //PWM 20ms改變一階
{
cnt_20ms = 20;
for(i=0; i<6; i++) pwm[i]++;
}
}
}
}
/********************** Timer0 1ms中斷函數 ************************/
void timer0 (void) interrupt 1
{
P3 = PWM_temp1; //影射RAM輸出到實際的PWM端口
if(++pwm_duty == PWM_DUTY_MAX) //PWM周期結束，重新開始新的周期
{
pwm_duty = 0;
PWM_temp1 = PWM_ALL_ON;
}
ACC = pwm_duty;
if(ACC == pwm[0]) P_PWM0 = PWM_OFF; //判斷PWM占空比是否結束
if(ACC == pwm[1]) P_PWM1 = PWM_OFF;
if(ACC == pwm[2]) P_PWM2 = PWM_OFF;
if(ACC == pwm[3]) P_PWM3 = PWM_OFF;
if(ACC == pwm[4]) P_PWM4 = PWM_OFF;
if(ACC == pwm[5]) P_PWM5 = PWM_OFF;
if(--cnt_1ms == 0)
{
cnt_1ms = Timer0_Rate / 1000;
B_1ms = 1; // 1ms標志
}
}

復制代碼

亚洲春色中文字幕久久久-三上亚,一吻二脱三床四吻胸,国产真实伦对白视频全集,在线毛片观看,精品成品入口黄网,国产毛aⅴ片久久久,亚洲AV色香蕉一区二区三区老师,萧皇后A级艳片,色情日本视频更新,99久久亚洲精品日本无码